Carbone Posted May 2, 2019 Share Posted May 2, 2019 I have limited experience with home Brew. I'm wondering if I can doctor crashed Gear. I E. Add more BB and reheat until it stabilizes. Other than not using enough solvent is there any other reason gear would not stay dissolved? Quote Link to comment Share on other sites More sharing options...
Carbone Posted May 3, 2019 Author Share Posted May 3, 2019 6 hours ago, bebeav said: A little more detail about the brew would help to get a better picture of the situation and helping you. I was attempting 50ml Test Cyp @ 250mg/ml using this recipe Test Cyp Powder - 12.5g Benzyl Alcohol - 1ml Benzyl Benzoate - 10ml Grape seed Oil - 27.65 ml I Fully dissolved the power into the BB BA using a beaker in a water bath. Added the GSO which was preheated. kept the mixture in the water bath and made sure it was completely homogenous. Then ran it through a 0.22 filter into a sterile vial. Crashed into a solid white mass approximately 2 hours later. Thanks for the help Quote Link to comment Share on other sites More sharing options...
StraightSideways Posted May 3, 2019 Share Posted May 3, 2019 (edited) 21 minutes ago, Carbone said: I was attempting 50ml Test Cyp @ 250mg/ml using this recipe Test Cyp Powder - 12.5g Benzyl Alcohol - 1ml Benzyl Benzoate - 10ml Grape seed Oil - 27.65 ml I Fully dissolved the power into the BB BA using a beaker in a water bath. Added the GSO which was preheated. kept the mixture in the water bath and made sure it was completely homogenous. Then ran it through a 0.22 filter into a sterile vial. Crashed into a solid white mass approximately 2 hours later. Thanks for the help Asked a buddy of mine that brews quite a lot, he follows a recipe that would come up with this for your 50ml: 1ml BA 7.5ml BB 30ml GSO Yours doesn't seem too far off. However you've got less carrier oil and more BB. Edit: Also supposedly he likes it even more with less BB than 7.5. Edited May 3, 2019 by StraightSideways Quote Link to comment Share on other sites More sharing options...
Carbone Posted May 4, 2019 Author Share Posted May 4, 2019 Worked like a charm, thank you. I added a little BB and more carrier oil. As soon as the Brew got close to the 200mg/ml mark it held. So far it's been stable all night. Quote Link to comment Share on other sites More sharing options...
baku Posted September 18, 2019 Share Posted September 18, 2019 oxymetholone injectable recipe: 50ml @ 50mg/ml 2.5 grams Anadrol (2.5ml) 2ml BA 2ml BB 5ml guaiacol 40 ml GSO Oil I took the most liquid top of it for a few guys that knew that I had some issues with it and as they state it worked anyway, but now i have jar filled with green jelly. Tried to add a little more oil and reheat, its better only when rly hot. Do You think that I could somehow save the product? Quote Link to comment Share on other sites More sharing options...
NorthernLifters Posted September 20, 2019 Share Posted September 20, 2019 On 9/18/2019 at 12:23 PM, baku said: oxymetholone injectable recipe: 50ml @ 50mg/ml 2.5 grams Anadrol (2.5ml) 2ml BA 2ml BB 5ml guaiacol 40 ml GSO Oil I took the most liquid top of it for a few guys that knew that I had some issues with it and as they state it worked anyway, but now i have jar filled with green jelly. Tried to add a little more oil and reheat, its better only when rly hot. Do You think that I could somehow save the product? Standard guaicol use is 2x per gram. So you used the correct amount. But why is your ba equal to bb? That's where the problem is. Bb is what thins out the oil Quote Link to comment Share on other sites More sharing options...
baku Posted September 20, 2019 Share Posted September 20, 2019 Do You think that more bb would help now? Or its too late to apologise : > Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.